tournevice
OSNN Junior Addict
- Joined
- 13 Oct 2004
- Messages
- 17
Hi there
I've got a problem whith my graphic card. It's a radeon 9200SE. I'm using xorg and the problem is that I can't load the glx and dri modules together without seeing my machine freezing... I've got a beautiful blackscreen and I really can't do anything...
I'm searching with google for this problem but I don't find anything that explains how to fix this. If you know how, please tell me
A dmesg | grep drm shows my graphic card...
At the end of /var/log/Xorg/0.log, I've got this (I don't have any warning messages or error messages :/ ):
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Fatal server error:
Caught signal 11. Server aborting
[...]
(II) RADEON(0): Wrote: rd=12, fd=101, pd=3
(==) RADEON(0): Write-combining range (0xa0000,0x10000) was already clear
Here is my xorg.conf shortened
Section "Module"
[...]
# This loads the Type1 and FreeType font modules
Load "GLcore"
Load "dbe"
Load "dri"
Load "type1"
Load "freetype"
Load "glx"
EndSection
Section "DRI"
Mode 0666
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
[...]
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "acer"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5 - 64.3
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-100
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "radeon 9200SE"
Driver "radeon"
VendorName "ATI Technologies Inc"
BoardName "Radeon 9200SE"
BusID "PCI:1:0:0"
Option "AGPMode" "4" # I've tried 1 but it's still not working though
#Option "EnablePageFlip"
#VideoRam 131072
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "radeon 9200SE"
Monitor "acer"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
I've got a problem whith my graphic card. It's a radeon 9200SE. I'm using xorg and the problem is that I can't load the glx and dri modules together without seeing my machine freezing... I've got a beautiful blackscreen and I really can't do anything...
I'm searching with google for this problem but I don't find anything that explains how to fix this. If you know how, please tell me
A dmesg | grep drm shows my graphic card...
At the end of /var/log/Xorg/0.log, I've got this (I don't have any warning messages or error messages :/ ):
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Fatal server error:
Caught signal 11. Server aborting
[...]
(II) RADEON(0): Wrote: rd=12, fd=101, pd=3
(==) RADEON(0): Write-combining range (0xa0000,0x10000) was already clear
Here is my xorg.conf shortened
Section "Module"
[...]
# This loads the Type1 and FreeType font modules
Load "GLcore"
Load "dbe"
Load "dri"
Load "type1"
Load "freetype"
Load "glx"
EndSection
Section "DRI"
Mode 0666
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
[...]
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "acer"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5 - 64.3
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-100
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "radeon 9200SE"
Driver "radeon"
VendorName "ATI Technologies Inc"
BoardName "Radeon 9200SE"
BusID "PCI:1:0:0"
Option "AGPMode" "4" # I've tried 1 but it's still not working though
#Option "EnablePageFlip"
#VideoRam 131072
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "radeon 9200SE"
Monitor "acer"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection