new Motherboard

Discussion in 'General Hardware' started by rabalder, Jul 16, 2002.

  1. rabalder

    rabalder Guest

    I just got a new motherboard,cpu,memory and AGP card. Now I cant start the pc,got stop screen.


    Abit BD711, P4 1800,and Asus AGP card V7100 series

    Anybody please help??:)
  2. vdubVR6

    vdubVR6 Guest

    :D Dont forget to make sure your agp card is in all the way. if you havent already,
  3. rabalder

    rabalder Guest


    Hm,I have tried and checked but it stops hard still. I have to take out all cards but AGP and try again. Bios is from april2002,so that should be ok,but the cpu is P4 1,8ghz 400.Northwood, 512 cache.

    in bios softmeny it says 1800/100,should't it be 1800/400?

    it must be something about bios or the hardware???
  4. vdubVR6

    vdubVR6 Guest

    so u can get 2 BIOS, just cant boot up?,..
  5. dejav00

    dejav00 Guest


    Did you look the stop error up at microsoft?
  6. rabalder

    rabalder Guest


    Yes I got to Bios,and a little bit further.It does the hole boot thing,then just before its finished I got the stop screen.:confused:
  7. Friend of Bill

    Friend of Bill What, me worry?

    1800/100 in BIOS is correct. Remember, P4's are "Quad Pumped." Set memory to SPD if it is not already.
  8. UniSol

    UniSol I'm all ears

    Have you reistalled the OS?
  9. gonaads

    gonaads Beware the G-Man Political User Folding Team

    It's more than likely your memory.
    Set all memory settings in BIOS to default, or the slowest they can be and reboot.
    If it boots, then shut down and bootup into BIOS and 1 at a time readjust your memory settings. Bootup after each setting adjustment to see what happens.
    Well that's if it is your mem settings. :D
  10. rabalder

    rabalder Guest


    I have tried the mem changing but still the same
  11. Hipster Doofus

    Hipster Doofus Good grief Charlie Brown

    Melbourne Australia
    What about this?

  12. dazzler

    dazzler Guest

    Are you using your old hard drive if so wouldnt this throw a wobbler (Technnical Term) if it hasn't been formatted.
  13. rabalder

    rabalder Guest


    No I have not reinstalled the OS,I need some files from the hd first. I have tried with another HD from another pc.but the same. I have read erlierer in this forum about XP and new motherboards and the problems around.but I do not find it again. No one of my other pc support larger disk then 40 gb,so I can not put it tin there as aslave to copy the files I need.Anyone now how to solve this without buying a new pc ?;)
  14. Friend of Bill

    Friend of Bill What, me worry?

    BD7 Raid II's have a problem with memory if all banks are filled. Try posting with only 1 memory slot filled.
  15. loose the abit lol
  16. Ford Prefect

    Ford Prefect Guest

    I dug this up at microsoft's technet site, hope it helps.

    The Stop 0x7B message indicates that Windows XP Professional has lost access to the system partition or boot volume during the startup process. Installing incorrect device drivers when installing or upgrading storage adapter hardware typically causes stop 0x7B errors. Stop 0x7B errors could also indicate possible virus infection.

    Interpreting the Message
    This Stop message has four parameters:

    The address of a Unicode string data structure representing the Advanced Reduced Instruction Set Computing (RISC) Computing (ARC) specification name of the device at which you attempted startup.
    Pointer to ARC name string in memory.
    This value is 0x00000000 (zero).
    This value is 0x00000000 (zero).
    The first parameter typically contains two separate pieces of data. For example, if the parameter is 0x00800020, 0x0020 is the actual length of the Unicode string and 0x0080 is the maximum ARC name string length. The next parameter contains the address of the buffer. This address is in system space, so the high-order bit is set.

    If the file system is unable to mount the boot device or simply does not recognize the data on the boot device as a file system structure, the following parameter definition applies:

    The address of the device object that could not be mounted.
    Error code value or 0x00000000 (zero).
    This value is 0x00000000 (zero).
    This value is 0x00000000 (zero).
    The value of the first parameter determines whether the parameter is a pointer to an ARC name string (ARC names are a generic method of identifying devices within the ARC environment) or a device object, because a Unicode string never has an odd number of bytes, and a device object always has a Type code of 0003.

    The second parameter is very important because it can indicate whether the 0x7B Stop message was caused by file system issues or problems with storage hardware and drivers. Values of 0xC000034 or 0xC000000E typically indicate:

    Disks or storage controllers that are failing, defective, or improperly configured.
    Storage-related drivers or programs (tape management software, for example) that are not fully compatible with Windows XP Professional.
    Resolving the Problem
    The following suggestions are specific to Stop 0x7B errors. For additional troubleshooting suggestions that apply to all Stop errors, see "Stop Message Checklist" later in this appendix.

    During I/O system initialization, the controller or driver for the startup device (typically the hard disk) might have failed to initialize the necessary hardware. File system initialization might have failed because of disk or controller failure, or because the file system did not recognize the data on the boot device.
    Repartitioning disks, adding new disks, or upgrading to a new disk controller might cause the information in the Boot.ini file, or Boot Manager, to become outdated. If this Stop message occurs after installing new disks to your system, edit the Boot.ini file or adjust the Boot Manager parameters to allow the system to start. If the error occurs after upgrading the disk controller, verify that the new hardware is functioning and correctly configured. For more information about the Boot.ini file, see "Troubleshooting Startup" in this book.
    Verify that the system firmware and disk controller BIOS settings are correct and that the storage device was properly installed. If you are unsure, consult your computer's documentation about restoring default firmware settings or configuring your system to auto-detect settings. If the error occurs during Windows XP Professional setup, the problem might be due to unsupported disk controller hardware. In some cases, drivers for new hardware are not in the Windows XP Professional library, and you need to provide additional drivers to complete the Windows XP Professional setup successfully. If this is the case, follow the hardware manufacturer's instructions when installing drivers. Periodically check for driver and firmware updates.
    Hard disk corruption can also cause this Stop message. For more information about checking hard disk integrity, see the instructions provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this appendix.
    Problems that cause 0x7B errors might also cause Stop 0xED errors. For more information about 0xED Stop messages, see "Stop 0x0000007B or INACCESSIBLE_BOOT_DEVICE" later in this appendix.
    For more information about Stop 0x7B messages, see the Microsoft Knowledge Base link on the Web Resources page at Search using keywords winnt, 0x0000007B, 0x7B, and Txtsetup.oem.
  17. Friend of Bill

    Friend of Bill What, me worry?

    Were all getting out of the woods now:)
  18. rabalder

    rabalder Guest

    mb again

    Yes all are getting out of the woods but MS.

    I think that the idea about bootdevice not reachable is good. But MS says bla bla bla. How do I fix the bootsequence,that says MS nothing about. Its like when keyboard don't work "Press F1 for help"

    I install XP on a new HD now,and then I will try to recover the Boot sector on the other one,I hope