H
Hercules
Guest
Hi, I know this might be out of the topic for this forum but I just want to try or if anyone knows another forum or website I can get advice to this problem. Well here I go.
----------------------------------------------------------------------------
----------------------
©ustom Spec's:Windows® XP.Pro.2002
1 x ST39102LC Seagate Cheetah 9LP 9.1GB HD (Primary), 1 x MX6L-080L-4 Maxtor
80 GB (Secondary Master), (S:\ Ramdisk 299MB FAT)
PIII 600 MHZ Asus P2B-DS Board BIO's version [1013],Matrox Millennium G400
32mb Max DualHead-5.72.021,512mb PC133 SD Rams,Sound Blaster Live value
CT4670,Hitachi DVD Rom,Plextor PX-w1210TS Burner 121032S Firmware 1.04.
LINKSYS 4-PORTSWITCH MODEL: BEFSR41 V.2 S/N:C2117138000. Firmware 1.42.6,
Mar 11 2002 Link to Cable modem @home.com.
----------------------------------------------------------------------------
-----------------------
This is what I have done.
1. Hook up the ST39102LC to 68-pin Ultra2 Scsi Connector slot in the
motherboard.
2. Booted up went into "BIOS Features Setup" to set HDD Sequence SCSI/IDE:
to SCSI
3. Save Booted up again, this time went into "Adaptec S AIC-7890 SCSI BIOS
build 20107" Press <CTRL><A>
4. In there there's two options 1. Scsi Disk Utilities displays information
on SCSI IDs 2. is config SCSI
controller ID is 7
ST39102LC is 2
Plextor cd rom is 4 or 5??
In there I VERIFY MEDIA the ST39102LC Hard Drive everything was okay.
After I formated the Drive that went okay.
5. I went to config and set boot sequence to ID 2
I rebooted, put in a WinXP cd in, also tried Win2k dunno why. got to the
part where set up is inspecting your hareware message and it stays there. Pauses, don't do anything, And I did not get to the blue screen where Winxp load drivers and ask me if i want to setup in this drive.
I'm not sure if I did anything wrong or even come close to doing this right.
If anyone with the knowledge of know any of this stuff please give me some adivise or info. THanxs for reading this.
----------------------------------------------------------------------------
----------------------
©ustom Spec's:Windows® XP.Pro.2002
1 x ST39102LC Seagate Cheetah 9LP 9.1GB HD (Primary), 1 x MX6L-080L-4 Maxtor
80 GB (Secondary Master), (S:\ Ramdisk 299MB FAT)
PIII 600 MHZ Asus P2B-DS Board BIO's version [1013],Matrox Millennium G400
32mb Max DualHead-5.72.021,512mb PC133 SD Rams,Sound Blaster Live value
CT4670,Hitachi DVD Rom,Plextor PX-w1210TS Burner 121032S Firmware 1.04.
LINKSYS 4-PORTSWITCH MODEL: BEFSR41 V.2 S/N:C2117138000. Firmware 1.42.6,
Mar 11 2002 Link to Cable modem @home.com.
----------------------------------------------------------------------------
-----------------------
This is what I have done.
1. Hook up the ST39102LC to 68-pin Ultra2 Scsi Connector slot in the
motherboard.
2. Booted up went into "BIOS Features Setup" to set HDD Sequence SCSI/IDE:
to SCSI
3. Save Booted up again, this time went into "Adaptec S AIC-7890 SCSI BIOS
build 20107" Press <CTRL><A>
4. In there there's two options 1. Scsi Disk Utilities displays information
on SCSI IDs 2. is config SCSI
controller ID is 7
ST39102LC is 2
Plextor cd rom is 4 or 5??
In there I VERIFY MEDIA the ST39102LC Hard Drive everything was okay.
After I formated the Drive that went okay.
5. I went to config and set boot sequence to ID 2
I rebooted, put in a WinXP cd in, also tried Win2k dunno why. got to the
part where set up is inspecting your hareware message and it stays there. Pauses, don't do anything, And I did not get to the blue screen where Winxp load drivers and ask me if i want to setup in this drive.
I'm not sure if I did anything wrong or even come close to doing this right.
If anyone with the knowledge of know any of this stuff please give me some adivise or info. THanxs for reading this.